Text Box: Designed by

Hybrid Geothermal Swimming Pool HVAC System

With the changing in temperatures by the seasons makes a Swimming pool a very good Geothermal Source and when incorporating an evaporative cooling tower will result in a energy efficient heating and cooling solution. Utilizing the energy from the swimming pool our designed is for new construction or retro fitting. A Retro Fit is a solution and this design is compatible with most all standard air handlers with evaporator coils that use R-22 refrigerant. Plus, this design can extend season swimming enjoyment!

The Swimming Pool is an excellent Hybrid Geothermal System.

There are several options to consider on this type of installation. Let’s start with a retro fit first. The overall design is incorporating an  Evaporative Subcooling Tower in to your existing swimming pool pump system. This will allow the tower to pull heat from the pool and heat the home in the winter. But at the end of summer and you are still cooling you home it will dump the heat energy into the pool and extend the pools swimming pleasure. The Heating and Air Conditioning layout is just like the residential Subcooling retro fit design. The actual installation layout will be designed by our engineer to properly fit the geographic region of the installation.

This installation may require help and assistance from a HVAC and Pool Company. This will depend on your knowledge and tools. Super Energy Efficient!

This also allows to place the Evaporative Subcooling Tower away from the house and remove the Air Condenser Units. You will use their pads and put our component house in their place. Should be able to use the existing breaker box and Freon lines. A true retro fit using existing Air Handlers inside the home.

This application is designed for a simple single or multi-zone (several air handlers inside) and Several air condenser units outside in different locations. Simple swap installation with any R-22 refrigerant (Freon) system. The tower and pump is wired 220v. What most pool pumps are wired. You must supply water to the tower and connect to our stainless steel flex 1/2” female fitting. PVC glue the 2 pipes from the pump housing to the Evaporative Subcooling tower.

These packages utilize only one Evaporative Subcooling Water Tower. The Copper Heat Exchanger is a close loop water Coil. For each compressor there is a matching cupro nickel Freon/Water Heat Exchanger. By only having one Tower you can place it anywhere and run the Coil water lines to each Zone Pad. Our Housing will hold a compressor and Freon/Water Exchanger where the old Air Condenser was located at.

This package is for two or three Zone (Inside Air Handlers) systems. Designed to replace multiple Outside Air Condensers at different locations.

 

These packages include:

 

One Thermco Evaporative Subcooling Tower.

Pump Housing & Control Panel

One Water Pump for tower.

 

AND

 

One compressor (2-5 ton) (We will call you to verify size)

One cupro nickel Freon/Water Heat Exchanger

One Component Housing Box

 

 

 

 

OR

 

Two compressors (2-5 ton) (We will call you to verify sizes)

Two cupro nickel Freon/Water Heat Exchangers

Two Component Housing Boxes

 

 

 

OR

 

Three compressors  (2-5 ton) (We will call you to verify sizes)

Three cupro nickel Freon/Water Heat Exchangers

Three Component Housing Boxes

What is a Freon/Water Heat Exchanger?

This is a component that receives the cold water from the Evaporative Subcooling Tower and inter-circles the Freon line to cools it before going to the condenser (compressor).

Single Zone -  This will replace your old  Outside Condenser Unit

Multiple Zones / These will replace your old  Outside Condenser Units.

Not Sure what to order, refer to YOUR LAYOUT.

Need Help? Call (512) 704-8200

Need Help? Call (512) 704-8200

SP1

SP3

SP2

Placement Planning:

 

Our Evaporative Fluid Cooler may be installed remotely, away from the loop. This choice may require a Flow Switch (supplied). This flow and temperature control will turn on/off Tower pump and fan. Recommended to be placed by the Swimming Pool pump system.

 

Water access needs to be considered. You will be connecting into a ¾ stainless steel standard female thread fitting.

 

Ball valve is in place to divert flow to the tower from the loop.  The tower should be able to handle all of the flow or you can open the valve a little bit to allow water to by pass the tower if the tower restricts the flow too much.  Just open the by pass ball valve little by little so most of the flow goes to the tower.

 

The Product:

 

All loop connections are 1 ½ PVC. You will connect into a Slip joint.

 

Attractive all fiberglass cabinet cannot corrode. Never requires painting. Air inlet windows designed to keep sunlight out which eliminates algae growth to help eliminate maintenance concerns. Fiberglass basin designed to eliminate freeze damage. Pump is protected by low wattage heat strips. High efficiency evaporative fluid copper coil design, commercial PVC evaporative media & Fittings, water Spray Nozzles, Durable plastic, non-corrosive and non-fouling. Aluminum body Fans, High Efficiency multi-speed motors, epoxy coated frame, precision balanced plastic blades for quiet, trouble-free service and salt air resistant.

 

Manufacture offers a 15 Year Warranty on the unit, 3 years on the pump and fan.

All Prices FOB Austin, Texas - Freight Collect

$8,995.00

$12,495.00

$15,995.00

Call to Order

Call to Order

Energy Conservation Products